Відео

Do you have any idea on what plus 2 or 4 base pad works with these pre ban mag and another question is my mags don’t drop when I hit the mag release it’s like it sticky not sure

Helpful video, thank you.

3/16 lmfa 😅

It's a good stove if you use a windscreen, I dont know why Vargo Outdoors took it off the market. Thank you for sharing 👍

Worked on my 2010 Toyota Sienna! I used WD-40 White Lithium Grease, which is thicker and will keep the door hinge lubricated longer. I also use it on squeaky door hinges at home and on noisy roof air vents. Thanks for the video, very much appreciated! Thank you for saving us $$$

I have that parallax adjustment ring issue on a new scope. It's under a 2-year guarantee, so I don't think I'll be the one fixing it, but this video has confirmed my understanding of the problem. And if the supplier sends me a new scope today without asking for my faulty one to be returned I can now work out how to slip the adjustment ring to make the original scope into a serviceable spare. Thanks for the video, it was exactly what I needed today.

My turret screws out of the scope and does not click anymore. Anyone know what to do?

Cover parts in Vaseline/jelly or tape off area you don’t want to ruin so you don’t have anything stick or bond to the wrong area . You can use baking soda to fill in the crevices make sure the cracks are filled properly and drop by drop add instant nail glue or clear epoxy is a good alternative let it cure fine sand and paint if need but that should make it stronger than it was before lol

Great explanation!

Wow i fixed mine in like 10 seconds

I'm trying to figure out how to change the barrel on the gun, the barrel on mine is cracked

Best and most discriptive clearly showed where it was . Best way to remove it. He's done this before.

I was hoping you would take the spiral erector out

Short, concise and well explained. Thank you!

😎👍😎

Thank you!! I have a G17 pre-ban mag that looked exactly like yours. I gave it the same "procedure", and if it lasts me another 5,000 rounds, I'll be absolutely thrilled! I'm not sure where you're located, but I'm in MA (Yes. a genuine Masshole!), and G17 pre-ban mags are now selling between $160-$200, and that's if you can even find them! A great video!

Just got a new scope (cheap) need to adjust parallax. Was looking for this video. Thank you

I was given on of these shotguns for helping clean up an estate. I don’t see any indication of the choke of the barrel. It a conventional barrel without a poly choke. How would I be able to determine the choke?

Struggling with the sear spring,any advice?

I just inherited a model 31. Went to clean it and I couldn't figure out how to lock the bolt open. Is there a trick to it? Any and all help will be much appreciated! Thanks! Mike

Thank you, Brother!, I finally got mine fixed, You're the man!

I put this on a .22 rifle that my girlfriend likes to use. It’s not the highest quality or the most accurate but it’s simple, cheap, and fun to use.

What position is the spring in front supposed to be in? It flops back and forth but you never get back to proper position in the video.

Im still wondering why it's banned

I TURN AND TURN AND NOTHING HAPPENS EHAT AM I DOING WRONG😊

have you had any experience with repairing a scope that no longer holds zero?

Way cool! Thanks for the info!!

Esiest access shown to this part! Thank you!

Changed mine to new and still, where should I look next?

Use gorilla glue

Thanks for this video, like some others the lifter spring/lifter/throat assembly has given me problems - after rewatching a few times and seeing drhine6271's comment below I came up with an easy method to get it right with any of the available springs (I have seen 2 different springs for sale that look nothing like the one my rifle came with). Start with the spring installed on its pin. Leave the halves of the throat aside and install the lifter with its pin, engaging the notch on the spring (easy when the throat is not in the way). Install one half of the throat by sliding the pin far enough aside to let it in, keeping pressure on the lifter so it can't push up off of the spring. Then slide the pin the other way, install the other half of the throat, and finally install the roll pin holding the throat halves in place. Easy!

Good info to have! Thank you!

Good job 👍 Thanks for sharing.

wondering if u have any suggestions regarding why the lift gate doesn't move all the way up when pumping with a shell

Great video. Do you lube (mild, heavy) the action and any suggestions for fixing failure to eject issues?

After about 50 attemps over 3 weeks finally got it. I put the roll pin in last, without the roll pin in you can lift up the magazine throat (both sides) so you can use a small screwdriver and slide spring into the notch . Then if you keep downward pressure on the lifter it will stay in place until you replace the magazine throat roll pin

Not the same part number for all of the 4.0 engines, for 98 and newer, 97 is a totally different part.

Wow great vid

The OEM part is Motorcraft SW 8368 for the oil pressure sender. Autozone was the lowest price I could find at $10.19.

IF THIS SENSOR GOES BAD,WILL IT LEAK BEFORE GOIN TOTALLY OUT? I SAW A PUDDLE OF CLEAR FLUID IN THE AREA OF THIS SENSOR. DIDNT DRIVE FOR TWO DAYS. FIVE MILES INTO ERRAND. ZERO OIL PRESSURE, SOUNDED LIKE A DIESEL W/O VALVE COVERS. I GOT HOME AND HAVE BEEN YOUTUBING FOR TWO DAYS.. ANY INFORMATION IS DEEPLY APPRECIATED, THX FOR POSTING!

My gauge needle is poijting totally on the opposite side it should be,

As a welder, I can tell why the cracks came back. You need more penetration. You have a steel insert on the back so you can penetrate deep without worry. You should have also squeezed the crack shut and then welded it. Put a nice fat bead on it. sand it down until it fits but try to leave as much as possible. If done right, the area will be stronger than it was before it cracked.

I have one of those scopes problem is it has no reticle no lines or anything Its basically just a spotter scope now I want to fix it since I bought it for 20 bucks and I want to put it on my rifle it's not a pellet rifle but what's the difference between pellet and 308 I just need something besides iron sights

Qoyil maqom

Great video ... I have a tasco world class plus 8-32 with AO that's out bad.. I'm try and fix it ..it's on a 10/22

thank you !!

修个毛线，我在义乌直接帮你买个吧，才$15

What this DS doesn't tell you is there is a little groove cut in the lifter that the top of the spring sits in. That's why it hard to get together.

Let's goooo!